伊人色综合久久天天五月婷-人妻体体射精一区二区-国产又粗又猛又色又免费-亚洲一区二区二区三区在线观看

服務熱線: 400-117-8816
           13406879330

扭剪扳手,扭剪螺栓專用扳手,扭剪電動扳手,扭剪槍生產廠家

當前位置:首頁>技術文獻定扭矩電動扳手的使用應該注意什么?

定扭矩電動扳手的使用應該注意什么?

來源:http://www.sxmingxi33.cn日期:2020-08-14 發布人:admin

1、電源的連接

1. Connection of power supply
先將主機的三芯插頭插入控制儀相應的插座上,然后將控制儀上的電源線接入電網。綠/黃雙色芯線為接地線。
First, insert the three core plug of the host into the corresponding socket of the controller, and then connect the power line of the controller to the power grid. The green / yellow core wire is the grounding wire.
工作結束后,以相反方向拆卸。
After the work is finished, dismantle in the opposite direction.
2、螺栓的扭緊操作
2. Tightening operation of bolts
1)裝上反力支架,并緊固螺釘。開動主機,使方頭銷孔與反力支架孔相對應,然后裝入扳手套筒,插上銷釘,并用橡膠圈固定。
1) Install the reaction support and tighten the screws. Start the main engine to make the square head pin hole correspond to the reaction support hole, then install the wrench socket, insert the pin, and fix it with rubber ring.
2)將控制儀的扭矩旋扭調到所需扭矩值,將主機正反開關撥到正轉位置,把扳手套筒套在螺紋連接件的六方上。
2) Adjust the torque of the controller to the required torque value, turn the positive and negative switch of the host to the forward rotation position, and put the wrench socket on the hexagon of the threaded connector.
3)按下電源開關,扳手啟動。當反力支架力臂靠牢支點時(支點可以是鄰近的一只螺栓或其他可做支點的位置)螺栓開始擰緊。當螺栓扭矩達到預定扭矩時,扳手自動停止,緊固完成,放開電源開關,進行下一只螺栓的緊固工作。
3) Press the power switch to start the wrench. When the force arm of the reaction support is firmly against the fulcrum (the fulcrum can be a nearby bolt or other fulcrum position), the bolt begins to tighten. When the bolt torque reaches the predetermined torque, the wrench will stop automatically and the tightening is completed. Release the power switch to tighten the next bolt.
4)扳手自動停止后,靠反力支架的彈性形變力,使支架力臂自動脫離支點,取下扳手。如力臂不能脫離支點時,可撥動正反開關,點動電源開關,扳手即可取下。
扭剪扳手
4) After the wrench stops automatically, the arm of the bracket will automatically break away from the fulcrum by the elastic deformation force of the reaction support, and then the wrench can be removed. If the force arm can not be separated from the fulcrum, the positive and negative switch can be turned, and the power switch can be touched to remove the wrench.
3、螺栓的拆卸操作
3. Bolt removal
扳手在拆卸螺栓(反轉)時,其操作方法與擰緊操作相同,只是將正反開關撥到反轉位置,螺栓卸松后防開電源開關。
When the wrench is removing the bolt (reversing), the operation method is the same as that of tightening, but the positive and negative switch is turned to the reverse position, and the power switch is not opened after the bolt is loosened.
4、扭矩的選擇與調節
4. Selection and adjustment of torque
1)用戶可在100---3500Nm的范圍內任意選擇相應規格的電動扳手。
1) The user can choose the electric wrench of corresponding specifications in the range of 100-3500nm.
2)控制儀面板上有“扭矩調節”旋扭,刻有0—100刻度值,用以調節扭矩。
2) There is a "torque adjustment" knob on the panel of the controller, which is engraved with 0-100 scale value to adjust the torque.
3)調節方法:產品出廠帶有扭矩測試數據卡片,供用戶標定時參考,用戶可根據所需扭矩選擇某一刻度值,按照擰緊螺栓的操作方法,扭緊螺栓。用測力扳手或其他測力儀器測出螺栓的實際扭矩值,若扭矩值偏高,將旋扭向低刻度調節;若扭矩值偏低,則向高刻度值調節,反復幾次既可達到所需精確扭矩值。
3) Adjustment method: the product is provided with torque test data card for users' reference during calibration. The user can select a calibration value according to the required torque and tighten the bolt according to the operation method of tightening the bolt. The actual torque value of the bolt is measured with a force measuring wrench or other force measuring instruments. If the torque value is too high, adjust the torque to the low scale; if the torque value is low, adjust it to the high scale value. Repeat several times to achieve the required accurate torque value.
本文由扭剪扳手友情奉獻.更多有關的知識請點擊:http://www.sxmingxi33.cn 我們將用真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.
For more information, please click: http://www.sxmingxi33.cn  We will be sincere attitude. To provide you with a comprehensive service. More relevant knowledge we will continue to contribute to you. Please look forward to

国产老妇伦国产熟女91| 综合欧美日韩一区二区三区| 午夜成人理论片在线观看| 亚洲国产成久久成人综合一区| 天天日天天干天天天天操| 欧美办公室大鸡巴| 男人扒开女人腿狂躁免费| 午夜福利国产三级片| 喜欢被粗大阴茎插入| 亚洲福利小视频在线观看| 国产欧美日本韩国一区二区| 阴茎大头插少妇蜜穴视频| 2021国产一区二区岛国| 操俄罗斯美女bb| 男人大鸡巴操女人的大逼| 伊人网在线免费视频| 亚洲欧美日韩清纯唯美第一区| 欧美亚洲另类天天综合网| 日国产精品1卡二卡三卡| 午夜精品福利一区二区三区蜜桃p| 国精品午夜福利视频导航| 大鸡鸡插我骚逼视频| 熟妇丰满大阴户熟妇啪啪| 韩国精品视频一区二区在线观看| 国产一区二区在线观看精品| 妓女综合网在线观看| 高清最新操逼吃鸡巴视频| 亚洲AV无码一区二区三区系列| 日本一区二区在线高清| 中文字幕乱码人妻一区二区三区| 爆操大奶子美女视频| 日日爱黄色毛片视频| 国产精品一区二区三区色噜噜 | 中日韩VA无码中文字幕| 中文无码av动作片| 久久久久有精品国产麻豆| 翘臀小穴在线观看| 日韩视频无码日韩视频又2020 | 加勒比在线不卡一区二区观看| 亚洲综合区欧美一区二区| 狗狗大鸡巴狂操美女|